Yanmar ZT370 Operation Manual Download Page 12 | Manualshive

Page: 12 / 60

background image

SAFETY

8

ZT370 Operation Manual

NOTICE

Only use replacement parts specified.
Other replacement parts may affect
warranty coverage.

Never attempt to modify the stern-drive’s
design or safety features.

Failure to comply may impair the
stern-drive’s safety and performance
characteristics and shorten the
stern-drive’s life. Any alterations to this
stern-drive may affect the warranty
coverage of your stern-drive.

Never use the stern-drive lifting eye to lift
the engine and stern-drive as an
assembly. Use the engine lifting eyes to lift
the engine and stern-drive. Only use the
stern-drive lifting eye to lift the stern-drive
as a separate component.

The anode of the stern-drive is only
calculated for the stern-drive. Changing
the material of the propeller may require
additional anodes to be installed on the
stern-drive.

Anytime the boat is left in the water and
the engine is not running, the drive must
be left in the fully down position. This will
keep the anodes in the water and will keep
the exhaust pipe engaged with the exhaust
port of the drive.

ZT370_OM.book 8 ページ２０１３年９月２７日　金曜日　午前１０時１６分

«
...
10
11
12
13
14
...
»

Summary of Contents for ZT370





























































Reviews:

No comments

Related manuals for ZT370

Brand: MSI Pages: 169

126791-HMC764LP6C

Brand: Analog Devices Pages: 18

Brand: Caji Pages: 19

Brand: Supermicro Pages: 93

Brand: ALi Confidential Pages: 24

Brand: Maxus Pages: 59

Brand: JETWAY Pages: 55

Brand: TYAN Pages: 37

SUPER i2DMR-8G2

Brand: Supero Pages: 78

Brand: Acorp Pages: 71

ATX-KLS0 Series

Brand: Quanmax Pages: 69

Brand: ASROCK Pages: 125

z75a-g45 series

Brand: MSI Pages: 88

Brand: NXP Semiconductors Pages: 19

Brand: Quantum Design Pages: 59

Brand: Quantum Design Pages: 75

Brand: TYAN Pages: 117

Brand: Global Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands