Yanmar ZT370 Operation Manual Download Page 47

Page: 47 / 60

MAINTENANCE

12/05

ZT370 Operation Manual

8. Remove the case plate cover

(4,

Figure 13

), filter cover

(3,

Figure 13

), magnet (2,

Figure 13

)

and filter (1,

Figure 13

). Clean or

replace the filter and magnet.

Figure 13

9. Lower the stern-drive so that the

propeller shaft is level. Fill the
stern-drive through the oil fill/drain hole
with the specified oil until an air-free
stream of oil flows from the filter
opening. Install the filter, magnet, filter
cover and case plate cover.

10.Continue to fill the stern-drive with oil

through the oil fill/drain hole until an
air-free stream of oil flows from the oil
vent hole.

11.Install the oil vent plug and gasket.

Torque the oil vent plug.

12.Continue to pump gear oil into the oil

reservoir circuit until the gear oil
appears in the oil reservoir.

13.Fill the oil reservoir so that the oil level is

within the operating range (

Figure 14

NOTICE

Never overfill.

*1:

Quick Silver is a registered trademark of
Brunswick Corporation.

Figure 14

14.Ensure that the rubber gasket is inside

the cap and install the cap.

NOTICE

Never over-tighten.

Oil vent plug torque

N·m

lb-ft

039085-00X00

2 3

Model

Capacity

Fluid type

ZT370

2500 m

(85 oz)

Quick Silver

®*1

High Performance

Gear Lube

039051-00E00

OPERATING
RANGE Line

Oil reservoir cap

ZT370_OM.book 43 ページ２０１３年９月２７日　金曜日　午前１０時１６分

Summary of Contents for ZT370





























































Search results

Summary of Contents for ZT370

Reviews:

Related manuals for ZT370

Brands by name

Popular brands

Yanmar ZT370, Operation Manual

Search results

Summary of Contents for ZT370

Reviews:

Related manuals for ZT370

Brands by name

Popular brands