Yanmar ZT370 Operation Manual Download Page 19 | Manualshive

Page: 19 / 60

background image

PRODUCT OVERVIEW

12/05

ZT370 Operation Manual

15

Gear Housing Anodic Plates

The gear housing anodic plates
(1,

) are installed on the

underside of the antiventilation plate.

Figure 4

Ventilation Plate Anode

The ventilation plate anode (1,

installed on the front of the drive shaft
housing on top of the ventilation plate.

Figure 5

Trim Cylinder Anodes

The trim cylinder anodes (1,

installed on each trim cylinder.

Figure 6

Propeller Shaft Anode

The propeller shaft anode (1,

) is

located behind the aft propeller.

Figure 7

039037-00X00

1

039034-00X00

1

039035-00X00

1

039036-00X00

1

ZT370_OM.book 15 ページ２０１３年９月２７日　金曜日　午前１０時１６分

«
...
17
18
19
20
21
...
»

Summary of Contents for ZT370





























































Reviews:

No comments

Related manuals for ZT370

Brand: Acrosser Technology Pages: 7

Brand: Texas Instruments Pages: 23

Brand: AKM Pages: 30

Brand: ITX SECURITY Pages: 18

Brand: JETWAY Pages: 45

Brand: NXP Semiconductors Pages: 28

Brand: A-Trend Pages: 44

EVAL-AD2428WD1BZ

Brand: Analog Devices Pages: 6

Brand: NXP Semiconductors Pages: 35

Brand: NXP Semiconductors Pages: 2

Brand: Silicon Laboratories Pages: 13

Brand: Biostar Pages: 60

Brand: MSI Pages: 98

Brand: IEI Technology Pages: 163

Brand: JETWAY Pages: 47

Brand: Gigabyte Pages: 75

KIT34704BEPEVBE

Brand: NXP Semiconductors Pages: 39

Brand: TYAN Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands