Yanmar ZT370 Operation Manual Download Page 52

Page: 52 / 60

MAINTENANCE

ZT370 Operation Manual

■

Lubricating the cable and the
linkages

See Lubricating the shift cable (typical) on
page 40

■

Touching-up the stern-drive paint
and spray with corrosion guard

See Touching-up the stern-drive paint and
spray with corrosion guard on page 41

■

Changing the stern-drive oil

See Changing the stern-drive oil on
page 41

■

Retorqueing the rear engine
mounts

See Torqueing the rear engine mount bolts
on page 46

■

Replace of friction disc (Light
duty commercial applications
only)

Consult your authorized Yanmar Marine
dealer or distributor.

Perform the following maintenance every 2
years of operation.

• Replace U-joint bellows

• Replace control cable bellows

■

Replace U-joint bellows

Consult your authorized Yanmar Marine
dealer or distributor.

■

Replace control cable bellows

Consult your authorized Yanmar Marine
dealer or distributor.

Every 2 Years

ZT370_OM.book 48 ページ２０１３年９月２７日　金曜日　午前１０時１６分

Summary of Contents for ZT370





























































Search results

Summary of Contents for ZT370

Reviews:

Related manuals for ZT370

Brands by name

Popular brands

Yanmar ZT370, Operation Manual

Search results

Summary of Contents for ZT370

Reviews:

Related manuals for ZT370

Brands by name

Popular brands