Yanmar ZT370 Operation Manual Download Page 48

Page: 48 / 60

MAINTENANCE

ZT370 Operation Manual

15.Remove the pump from the oil fill/drain

hole. Quickly install the gasket and oil
fill/drain plug. Torque the oil fill/drain
plug.

16.Check the oil level in the oil reservoir

after first use.

17.Check the stern-drive oil level within

one week of the first use as follows:

1- Remove the oil vent plug

(1,

Figure 15

) and gasket

(2,

Figure 15

2- If necessary, add oil until an air-free

stream of oil flows from the oil vent
hole.

3- Install the oil vent plug and gasket.

Torque the oil vent plug.

NOTICE

Oil level in the oil reservoir will rise and
fall during stern-drive operation; always
check the level when the stern-drive is
cool and the engine is shut down.

Oil fill/drain plug torque

N·m

lb-ft

039055-00X00

ZT370_OM.book 44 ページ２０１３年９月２７日　金曜日　午前１０時１６分

Summary of Contents for ZT370





























































Search results

Summary of Contents for ZT370

Reviews:

Related manuals for ZT370

Brands by name

Popular brands

Yanmar ZT370, Operation Manual

Search results

Summary of Contents for ZT370

Reviews:

Related manuals for ZT370

Brands by name

Popular brands