Yanmar ZT370 Operation Manual Download Page 28

Page: 28 / 60

STERN-DRIVE OPERATION

ZT370 Operation Manual

1. Apply a liberal coat of lubricant to the

propeller shaft. Recommended
lubricants are shown in the table below.

2. Slide the forward thrust hub onto the

propeller shaft with the tapered side
toward the propeller hub (toward end of
propeller shaft).

3. Align the splines and place the

propeller on the propeller shaft.

4. Install and torque the front propeller

nut. Check the propeller at least every
20 hours.

5. Slide the aft thrust hub onto the

propeller shaft, with the tapered side
toward the propeller hub (toward end of
shaft).

6. Align the splines and place the

propeller on the propeller shaft.

7. Install and torque the rear propeller nut.

Check the propeller at least every 20
hours.

8. Install the propeller shaft anode bolt

with a washer. Torque the bolt.

Description

Where used

Urea grease water resistant

type, NLGI #2

Propeller

shaft

Lithium grease with PTFE

Front propeller nut torque

N·m

lb-ft

135

Rear propeller nut torque

N·m

lb-ft

Propeller shaft anode bolt torque

N·m

lb-ft

ZT370_OM.book 24 ページ２０１３年９月２７日　金曜日　午前１０時１６分

Summary of Contents for ZT370





























































Search results

Summary of Contents for ZT370

Reviews:

Related manuals for ZT370

Brands by name

Popular brands

Yanmar ZT370, Operation Manual

Search results

Summary of Contents for ZT370

Reviews:

Related manuals for ZT370

Brands by name

Popular brands