Yanmar ZT370 Operation Manual Download Page 18 | Manualshive

Page: 18 / 60

background image

PRODUCT OVERVIEW

14

ZT370 Operation Manual

Underwater Drive Coating

The lower gear case coating may be
damaged when hit by objects in the water,
or when having deposits removed from it.
The underwater coating must be inspected
at least once per year and when it is
believed that an object was hit that may
have caused damage. Repair and repaint
damaged areas immediately.

Observe the following precautions when
applying antifouling or marine paint to the
transom of the boat hull:

• Always follow the paint/coating

manufacturer’s directions for surface
preparation and application.

• Always use a high quality primer and

topcoat paint specifically designed for
aluminum outboards or stern-drives.

• Never paint the anodes installed on the

stern-drive.

• Never paint the Y-CaPS reference

electrode and/or anode.

• Never wash the stern-drive with a high

pressure washer. This could damage the
coating on the reference wire.

• Never paint the stern-drive with a

material that contains copper or tin.

• Never paint over drain holes, anodes,

Y-CaPS or other items specified by the
anode manufacturer.

Consult your authorized Yanmar Marine
dealer or distributor for assistance.

NOTICE

Galvanic corrosion damage, normal
maintenance and consumable parts are
not covered by the Yanmar limited
warranty.

Additional Protection

In addition to the corrosion protection
devices, take these steps to inhibit
corrosion:

1. Paint the stern-drive.

See Touching-up

the stern-drive paint and spray with
corrosion guard on page 41

2. Spray stern-drive components on the

inside of the vessel annually with
corrosion guard to protect the finish
from dulling and corrosion. External
stern-drive components may also be
sprayed.

3. Keep all lubrication points, especially

the steering system, shift and throttle
linkages, well-lubricated.

4. Flush the coolant system periodically,

preferably after each use.

NOTICE

Replace anodes if eroded 50 percent or
more.

NOTICE

Anytime the boat is left in the water and
the engine is not running, the drive must
be left in the fully down position. This will
keep the anodes in the water and will
keep the exhaust pipe engaged with the
exhaust port of the drive.

Figure 3

039030-00E00

Trim cylinder anodes

Y-CaPS
electrode

Ventilation
plate anode

Propeller shaft
anodes

Gear
housing
anodic
plates

ZT370_OM.book 14 ページ２０１３年９月２７日　金曜日　午前１０時１６分

«
...
16
17
18
19
20
...
»

Summary of Contents for ZT370





























































Reviews:

No comments

Related manuals for ZT370

1stMainboard VG33

Brand: FIC Pages: 38

Brand: ECS Pages: 56

Brand: ST Pages: 79

Brand: CIRCUIT DESIGN Pages: 9

Brand: AOpen Pages: 8

K9N6PGM2-V2 - Motherboard - Micro ATX

Brand: MSI Pages: 153

Brand: ASROCK Rack Pages: 83

MT9M031I12STCH-GEVB

Brand: ON Semiconductor Pages: 5

Freescale MCIMX6Q-SL

Brand: NXP Semiconductors Pages: 37

Brand: THine Pages: 13

Brand: Corvalent Pages: 71

Brand: Texas Instruments Pages: 21

Brand: Texas Instruments Pages: 19

LMK04906 Series

Brand: Texas Instruments Pages: 62

Brand: Gigabyte Pages: 8

Brand: SimCom Pages: 27

ITX-IC2M1026S Series

Brand: Intel Pages: 35

Brand: Freetech Pages: 69

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands