Yanmar ZT370 Operation Manual Download Page 43

Page: 43 / 60

MAINTENANCE

12/05

ZT370 Operation Manual

■

Lubricating the engine coupler

See Lubricating the engine coupler on
page 36

■

Checking the circuit for loose or
damaged connections

Check the electrical connections and leads
for damage and corrosion.

■

Testing the Y-CaPS unit output

See Yanmar Cathodic Protection System
on page 19

■

Checking the steering system for
loose, missing or damaged parts

Check the steering system and tighten any
loose parts, replace any missing or
damaged parts.

■

Checking the remote control for
loose, missing or damaged parts

See Remote Controls on page 16

■

Lubricating the shift cable and
the linkages

CAUTION

Never grease the steering cable while
extended. Hydraulic lock could occur
and cause loss of steering control.

Grease the steering cable grease fitting.

1. Turn the steering wheel until the

steering cable is fully retracted into the
cable housing. Apply approximately
three pumps of grease from a typical
hand-operated grease gun.

Note: If the steering cable does not

have a grease fitting, the inner
wire of the cable cannot be
greased.

2. Turn the steering wheel until the

steering cable (1,

Figure 6

) is fully

extended. Lightly lubricate the exposed
part of the cable.

Figure 6

3. Lubricate the steering system clevis pin

(1,

Figure 7

4. On dual engine vessels, lubricate the

tie bar clevis pin.

Description

Where used

Lithium grease with PTFE

Steering cable

Description

Where used

Urea grease water resistant

type, NLGI #2

Steering cable

Description

Where used

Urea grease water resistant

type, NLGI #2

Clevis pin

039079-00X00

039080-00X00

ZT370_OM.book 39 ページ２０１３年９月２７日　金曜日　午前１０時１６分

Summary of Contents for ZT370





























































Search results

Summary of Contents for ZT370

Reviews:

Related manuals for ZT370

Brands by name

Popular brands

Yanmar ZT370, Operation Manual

Search results

Summary of Contents for ZT370

Reviews:

Related manuals for ZT370

Brands by name

Popular brands