Yanmar ZT370 Operation Manual Download Page 31

Page: 31 / 60

STERN-DRIVE OPERATION

12/05

ZT370 Operation Manual

Figure 3

*1:

Quick Silver is a registered trademark of
Brunswick Corporation.

3. When replacing the cap, ensure that

the rubber gasket is inside the oil
reservoir cap and install the cap. Do not
over-tighten.

Check the Power Trim Pump
Fluid

NOTICE

Always check the oil level with stern-drive
in the full DOWN/TRIM-IN position.

1. Place the stern-drive in full

DOWN/TRIM-IN position.

2. Observe the oil level in the reservoir.

The oil level should be maintained
within the MIN and MAX lines
(2,

Figure 4

) on the reservoir

(1,

Figure 4

3. The oil level is low if it is below the MIN

line (1,

Figure 5

) on the reservoir. Fill

as necessary with the specified fluid.

See Fill the power trim pump fluid on
page 28

Description

Where used

BY3

series

Quick Silver

®*1

High Performance

Gear Lube or

GL-5 (SAE 80W90)

Oil reservoir

6LPA
series

8LV

series

Quick Silver

®*1

High Performance

Gear Lube

039051-00X00

039052-00X00

ZT370_OM.book 27 ページ２０１３年９月２７日　金曜日　午前１０時１６分

Summary of Contents for ZT370





























































Search results

Summary of Contents for ZT370

Reviews:

Related manuals for ZT370

Brands by name

Popular brands

Yanmar ZT370, Operation Manual

Search results

Summary of Contents for ZT370

Reviews:

Related manuals for ZT370

Brands by name

Popular brands