Yanmar 6LY3-STC Operation Manual Download Page 76

Page: 76 / 88

3. Close the drain cocks.

Note: Do not drain the coolant (freshwater

cooling system). If the coolant is drained, the

cooling system components could corrode.
Before placing the engine in storage,

perform the following:

1. Clean the outside of the engine, wiping

off any dust or oil.

2. Drain the fuel or fill the tank completely

to help prevent condensation inside the

tank.

3. Refill the heat exchanger with engine

coolant.

4. Cover the turbocharger, exhaust pipe,

etc. with vinyl sheets and seal them to

prevent moisture from entering.

5. Completely drain the bilge. Put the boat

in dry dock, if possible.

6. Waterproof the engine room to prevent

rain and seawater from entering.

7. During long-term storage, charge the

battery once a month to compensate for

the battery’s self-discharge.

RETURNING THE ENGINE

TO SERVICE

1. Replace the oil and the oil filter before

running the engine.

2. Supply fuel if the fuel in the fuel tank was

removed, and prime the fuel system.

3. Confirm that there is engine coolant in

the engine.

4. Operate the engine at idle speed for 1

minute.

5. Check fluid levels and check engine for

leaks.

LONG-TERM STORAGE

6LY3 LDC Operation Manual

Summary of Contents for 6LY3-STC
























































































Search results

Summary of Contents for 6LY3-STC

Reviews:

Yanmar 6LY3-STC, Operation Manual, Page: 76 / 88

Search results

Summary of Contents for 6LY3-STC

Reviews: