Yanmar 6LY3-STC Operation Manual Download Page 53

Page: 53 / 88

PERIODIC MAINTENANCE SCHEDULE

Daily and periodic maintenance are

important to keep the engine in its best

operating condition. The following is a

summary of inspection and servicing items

by inspection interval. Periodic

maintenance intervals should vary

depending on the uses, loads, fuels and

lubricating oils used, and handling

conditions, and are hard to establish

definitively. The following should be treated

as a general guide only. Periodic

Maintenance Procedures on page 50

gives a detailed explanation of which parts

must be inspected and the procedure for

doing so for each interval.

CAUTION! Establish a periodic

maintenance plan according to the

engine application and make sure to

perform the required periodic

maintenance at the intervals indicated.

Failure to follow these guidelines will

impair the engine’s safety and

performance characteristics, shorten

the engine’s life and may affect the

warranty coverage on your engine. See

your authorized Yanmar Marine dealer

or distributor for assistance when

checking items marked with a ●.

◯

: Check or Clean ◊: Replace ●: Contact your authorized Yanmar Marine dealer or distributor

System

Item

Periodic Maintenance Interval

Daily

(See Daily

Checks on

page 50.)

Every 50

hours or

monthly,

whichever

comes first

Every 250

hours or

three

months,

whichever

comes first

Every 500

hours or

six

months,

whichever

comes

first

Every 1000

hours or

one year,

whichever

comes first

Every 2000

hours or

two years,

whichever

comes first

Whole

Visual inspection of engine exterior

◯

Fuel System

Check the fuel level and refill if

necessary

◯

Drain the fuel tank

◯

Drain the fuel filter and fuel / water

separator

◯

Replace the fuel filter element

◊

(1st time)

◊

Check the fuel injector spray

pattern *

● *

(1st time)

●*

Overhaul and check fuel feed pump

●

Replace rubber fuel hoses

Replace every 2 years or every 2000 hours, whichever comes first.

Lubricating

System

Check the engine

oil level

Crankcase

◯

Replace the

engine oil

Crankcase

◊

(1st time)

◊

Replace the oil filter element

◊

(1st time)

◊

Clean engine oil cooler

●

PERIODIC MAINTENANCE

6LY3 LDC Operation Manual

Summary of Contents for 6LY3-STC
























































































Search results

Summary of Contents for 6LY3-STC

Reviews:

Yanmar 6LY3-STC, Operation Manual, Page: 53 / 88

Search results

Summary of Contents for 6LY3-STC

Reviews: