Yanmar 6LY3-STC Operation Manual Download Page 68

Page: 68 / 88

Clean Seawater and Engine Coolant

System

Rust and scale are deposited inside the

seawater and engine coolant system during

long use. This lowers cooling performance,

so it is necessary to clean and maintain the

following parts in addition to replacing the

coolant.

Relevant Coolant System Parts:

Seawater pump, engine oil cooler,

aftercooler, freshwater pump, freshwater

cooler, thermostat, etc.

See your authorized Yanmar Marine dealer

or distributor to clean the seawater and

engine coolant systems.

Replace Rubber Fuel Hoses

Rubberized fuel hoses tend to dry out and

become brittle after 2000 hours or 2 years of

engine operation, whichever comes first.

See your authorized Yanmar Marine dealer

or distributor to replace the rubber fuel

hoses.

EPA REQUIREMENTS

The EPA emission regulation is applicable

only in USA.

EPA Certification Plates

The engine has the EPA Certification Plates

(emission control label and light duty

commercial engine label) attached.

The labels are attached to the top of the

electronic control unit (ECU) cover plate

(Figure 9).

0006536

(119578-07701)

Figure 9

PERIODIC MAINTENANCE

6LY3 LDC Operation Manual

Summary of Contents for 6LY3-STC
























































































Search results

Summary of Contents for 6LY3-STC

Reviews:

Yanmar 6LY3-STC, Operation Manual, Page: 68 / 88

Search results

Summary of Contents for 6LY3-STC

Reviews: