Yanmar 6LY3-STC Operation Manual Download Page 21

Page: 21 / 88

ELECTRONIC CONTROL

SYSTEM (ECS)

the control equipment consists of the rocker

switch panel, the display, engine interface

module and the control head, which are

connected by the wire harness to the engine

(electronic governor and marine gear) for

remote control operation.

See Yanmar Electronic Control System

Operation Manual for LY3 Engines for a

more complete description of the electronic

control system (ECS).

Start

Eng ON

OFF

Emergency

Stop

Sub throttle active

Sub throttle

Model:i2 Module

0002022

(3)

(4)

(1)

(2)

(8)

(5)

(7)

(6)

(9)

Figure 4

1 – First Station Rocker Switch

Panel

2 – To Engine

3 – Interface Module Without

Trolling Interface Module with

Trolling (optional)

4 – To Engine

5 – To Marine Gear

6 – NMEA Tee and Terminators Kit

7 – NMEA Tee Connector

8 – Digital Display

9 – Control Head (shift and throttle)

PRODUCT OVERVIEW

6LY3 LDC Operation Manual

Summary of Contents for 6LY3-STC
























































































Search results

Summary of Contents for 6LY3-STC

Reviews:

Yanmar 6LY3-STC, Operation Manual, Page: 21 / 88

Search results

Summary of Contents for 6LY3-STC

Reviews: