Yanmar 6LY3-STC Operation Manual Download Page 54

Page: 54 / 88

◯

: Check or Clean ◊: Replace ●: Contact your authorized Yanmar Marine dealer or distributor

System

Item

Periodic Maintenance Interval

Daily

(See Daily

Checks on

page 50.)

Every 50

hours or

monthly,

whichever

comes first

Every 250

hours or

three

months,

whichever

comes first

Every 500

hours or

six

months,

whichever

comes

first

Every 1000

hours or

one year,

whichever

comes first

Every 2000

hours or

two years,

whichever

comes first

Cooling System Seawater outlet

◯

During Op-

eration

Check coolant level

◯

Check the seawater pump impeller

◯

◊

Replace the engine coolant

Every year. When Long Life Coolant (LLC) is used, replace every two years.

See Engine Coolant on page 29.

Clean and check the seawater pas-

sages

●

Clean seawater and engine cooling

system

●

Replace zinc anode

◊

Air Intake and

Exhaust System

Clean the air intake silencer

◯

Clean the exhaust / water mixing el-

bow

◯

◊

Clean the turbocharger blower

●*

Flush aftercooler

●

Electrical Sys-

tem

Check the alarm indicators

◯

Check the electrolyte level in the

battery

◯

Adjust the tension of the alternator

V-belt or replace V-belt

◯

◊

Check the wiring connectors

◯

Engine Cylinder

Head and Block

Check for leakage of fuel, engine oil

and engine coolant

◯

After Starting

Tighten all major nuts and bolts

●

Adjust intake / exhaust valve clear-

ance

●

(1st time)

●

Miscellane- ous

Items

Check the electronic control system

operation

◯

(1st time)

Adjust the propeller shaft alignment

●

(1st time)

●

Check / replace flexible engine

mounts

◯

◊

For EPA requirements, See EPA Requirements on page 62.

Note: These procedures are considered normal maintenance and are performed at the

owner’s expense.

PERIODIC MAINTENANCE

6LY3 LDC Operation Manual

Summary of Contents for 6LY3-STC
























































































Search results

Summary of Contents for 6LY3-STC

Reviews:

Yanmar 6LY3-STC, Operation Manual, Page: 54 / 88

Search results

Summary of Contents for 6LY3-STC

Reviews: