Yanmar 6LY3-STC Operation Manual Download Page 51

Page: 51 / 88

PRECAUTIONS

The Importance of Periodic

Maintenance

Engine deterioration and wear occurs in

proportion to length of time the engine has

been in service and the conditions the

engine is subject to during operation.

Periodic maintenance prevents unexpected

downtime, reduces the number of accidents

due to poor machine performance and helps

extend the life of the engine.

Performing Periodic

Maintenance

WARNING! NEVER block windows,

vents, or other means of ventilation if

the engine is operating in an enclosed

area. All internal combustion engines

create carbon monoxide gas during

operation. Accumulation of this gas

within an enclosure could cause illness

or even death. Make sure that all

connections are tightened to

specifications after repair is made to the

exhaust system. Failure to comply could

result in death or serious injury.

The Importance of Daily Checks

Periodic Maintenance Schedules assume

that the daily checks are performed on a

regular basis. Make it a habit of performing

daily checks before the start of each

operating day. See Daily Checks on page

50.

Keep a Log of Engine Hours and

Daily Checks

Keep a log of the number of hours the engine

is run each day and a log of the daily checks

performed. Also note the date, type of repair

(e.g., replaced alternator) and parts needed

for any service needed between the periodic

maintenance intervals. Periodic

maintenance intervals are every 50, 250,

500, 1000 and 2000 engine hours. Failure to

perform periodic maintenance will shorten

the life of the engine. NOTICE: Failure to

perform periodic maintenance will shorten

the life of the engine and may void the

warranty.

Yanmar Replacement Parts

Yanmar recommends that you use genuine

Yanmar parts when replacement parts are

needed. Genuine replacement parts help

ensure long engine life.

Tools Required

Before you start any periodic maintenance

procedure, make sure you have the tools

you need to perform all of the required tasks.

Ask Your Authorized Yanmar

Marine Dealer for Help

Our professional service technicians have

the expertise and skills to help you with any

maintenance or service related procedures

you need help with.

Required EPA Maintenance - USA

Only

To maintain optimum engine performance

and compliance with the Environmental

Protection Agency (EPA) Regulations, it is

essential that you follow the Periodic

Maintenance Schedule on page 47 and

Periodic Maintenance Procedures on page

50.

PERIODIC MAINTENANCE

6LY3 LDC Operation Manual

Summary of Contents for 6LY3-STC
























































































Search results

Summary of Contents for 6LY3-STC

Reviews:

Yanmar 6LY3-STC, Operation Manual, Page: 51 / 88

Search results

Summary of Contents for 6LY3-STC

Reviews: