Yanmar 6LY3-STC Operation Manual Download Page 69

Page: 69 / 88

Conditions to Ensure

Compliance with EPA Emission

Standards

This product is an EPA-approved engine.

The following are the conditions that must be

met in order to ensure that the emissions

during operation meet the EPA standards:

1. Ambient temperature: -20 to 40°C (-4 to

104°F)

2. Relative humidity: 80% or lower
The fuel and lubricating oil used should be

as follows:

• Diesel fuel oil: ASTM D975 No. 1-D or No.

2-D, or equivalent (minimum of cetane No.

45)

• Lubricating Oil: Type API, Class CD or

higher

Be sure to perform inspections as outlined

in Periodic Maintenance Procedures on

page 50 and keep a record of the results.

Pay particular attention to these important

points:

• Replacing the engine oil
• Replacing the lube oil filter
• Replacing the fuel filter
• Cleaning the intake silencer (air cleaner)
Note: Inspections are divided into two

sections in accordance with who is

responsible for performing the inspection:

the user or the maker.

Inspection and Maintenance

See Inspection and Maintenance of EPA

Emission-Related Parts on page 49 for the

EPA emission-related parts. Inspection and

maintenance procedures not shown in the

Inspection and Maintenance of EPA

Emission-Related Parts section are covered

in Periodic Maintenance Schedule on page

47.

This maintenance must be performed to

keep the emission values of your engine in

the standard range during the warranty

period. The warranty period is determined

by the age of the engine or the number of

hours of operation. See Yanmar Co., Ltd.

Limited Emission Control System Warranty

- USA Only on page 77.

PERIODIC MAINTENANCE

6LY3 LDC Operation Manual

Summary of Contents for 6LY3-STC
























































































Search results

Summary of Contents for 6LY3-STC

Reviews:

Yanmar 6LY3-STC, Operation Manual, Page: 69 / 88

Search results

Summary of Contents for 6LY3-STC

Reviews: