Yanmar 6LY3-STC Operation Manual Download Page 52

Page: 52 / 88

EPA Installation Requirements -

USA Only

The following are the installation

requirements for the EPA. Unless these

requirements are met, the exhaust gas

emissions will not be within the limits

specified by the EPA.

See Conditions to Ensure Compliance with

EPA Emission Standards on page 63 for

operating conditions.

Tightening Fasteners

Use the correct amount of torque when you

tighten fasteners on the machine. Applying

excessive torque may damage the fastener

or component and not enough torque may

cause a leak or component failure.

NOTICE: The tightening torque in the

Standard Torque Chart

should be applied only to the

bolts with a “7” head (JIS

strength classification: 7T).

Apply 60% torque to bolts that

are not listed. Apply 80% torque when

tightened to aluminum alloy.

Standard Torque Chart

Bolt diameter x

pitch (mm)

M6x1.0

M8x1.25

M10x1.5

M12x1.75

M14x1.5

M16x1.5

Tightening

Torque

N·m

11.0 ± 1.0

26.0 ± 3.0

50.0 ± 5.0

90.0 ±

10.0

140.0 ± 10.0

230.0 ± 10.0

kgf-m

1.1 ± 0.1

2.7 ± 0.3

5.1 ± 0.5

9.2 ± 1.0

14.3 ± 1.0

23.5 ± 1.0

lb-ft

8.0 ± 0.7

19.0 ± 2.1

37 ± 3.6

66.0 ± 7.2

103 ± 7.2

170 ± 7.2

PERIODIC MAINTENANCE

6LY3 LDC Operation Manual

Summary of Contents for 6LY3-STC
























































































Search results

Summary of Contents for 6LY3-STC

Reviews:

Yanmar 6LY3-STC, Operation Manual, Page: 52 / 88

Search results

Summary of Contents for 6LY3-STC

Reviews: