Yanmar 6LY3-STC Operation Manual Download Page 39

Page: 39 / 88

ENGINE OPERATION

This section of the Operation Manual

describes the diesel fuel, engine oil and

engine coolant specifications and how to

replenish them. It also describes the daily

engine checkout.

Before performing any operations within this

section, review the Safety section on

page 4.

WARNING

Fire and Explosion Hazard

NEVER jump-start the engine.

Sparks caused by shorting the

battery to the starter terminals

may cause a fire or explosion.

ONLY use the key switch to start the engine.

Sudden Movement Hazard

Be sure the boat is in open water away from

other boats, docks or other obstructions

before increasing rpm. Avoid unexpected

equipment movement. Shift the marine gear

into the NEUTRAL position any time the

engine is at idle.

To prevent accidental equipment

movement, NEVER start the engine in gear.

Sever Hazard

Keep children and pets away

while the engine is operating.

Exhaust Hazard

NEVER block windows, vents or

other means of ventilation if the

engine is operating in an

enclosed area. All internal

combustion engines create carbon

monoxide gas during operation and special

precautions are required to avoid carbon

monoxide poisoning.

6LY3 LDC Operation Manual

Summary of Contents for 6LY3-STC
























































































Search results

Summary of Contents for 6LY3-STC

Reviews:

Yanmar 6LY3-STC, Operation Manual, Page: 39 / 88

Search results

Summary of Contents for 6LY3-STC

Reviews: