manualshive.com logo in svg

Yamaha MTN850-A 2017, Service Manual, Page: 527 / 560

Share
Download
Yamaha MTN850-A 2017 Service Manual Download Page 527

ELECTRICAL COMPONENTS

8-170

b. Immerse the coolant temperature sensor “1”

in a container filled with coolant “2”.

TIP

Make sure the coolant temperature sensor ter-
minals do not get wet.

c. Place a thermometer “3” in the coolant.

d. Heat the coolant or let it cool down to the

specified temperatures.

e. Measure the coolant temperature sensor re-

sistance.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

3. Install:

•

Coolant temperature sensor

EAS30581

CHECKING THE THROTTLE POSITION 

SENSOR

1. Remove:

•

Throttle position sensor
(from the throttle bodies)

NOTICE

ECA17540

• Handle the throttle position sensor with

special care.

• Never subject the throttle position sensor

to strong shocks. If the throttle position

sensor is dropped, replace it.

2. Check:

•

Throttle position sensor maximum resistance
Out of specification 

 Replace the throttle

position sensor.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect the digital circuit tester (

) to the

throttle position sensor terminals as shown.

b. Measure the throttle position sensor maxi-

mum resistance.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

3. Install:

•

Throttle position sensor

TIP

When installing the throttle position sensor, ad-
just its angle properly. Refer to “ADJUSTING
THE THROTTLE POSITION SENSOR” on page
7-12.

EAS30582

CHECKING THE ACCELERATOR POSITION 

SENSOR

1. Remove:

•

Accelerator position sensor
(from the throttle bodies)

WARNING

EWA15960

• Handle the accelerator position sensor with

special care.

• Never subject the accelerator position sen-

sor to strong shocks. If the accelerator po-

sition sensor is dropped, replace it.

2. Check:

•

Accelerator position sensor maximum resis-
tance
Out of specification 

 Replace the accelera-

tor position sensor.

Coolant temperature sensor

16 N·m (1.6 kgf·m, 12 lb·ft)

Resistance

1.20–2.80 k

3

1

2

T

R

.

.

Digital circuit tester (CD732)

90890-03243

Model 88 Multimeter with tachom-

eter

YU-A1927

•

Positive tester probe 

blue “1”

•

Negative tester probe 

black/blue “2”

Resistance

1.08–2.52 k

B

L

B

/

L

W

2

1

Summary of Contents for MTN850-A 2017

















































































































































































































































































































































































































































































































































































Reviews:

No comments