manualshive.com logo in svg

Yamaha MTN850-A 2017, Service Manual, Page: 165 / 560

Share
Download
Yamaha MTN850-A 2017 Service Manual Download Page 165

REAR WHEEL

4-20

EAS30910

REMOVING THE REAR WHEEL

NOTICE

ECA21390

Keep magnets (including magnetic pick-up

tools, magnetic screwdrivers, etc.) away

from the rear wheel sensor “1”, otherwise

the wheel sensor may be damaged, resulting

in improper performance of the ABS.

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there is

no danger of it falling over.

TIP

Place the vehicle on a maintenance stand so
that the rear wheel is elevated.

2. Remove:

•

Rear brake caliper “1”

•

Rear wheel sensor

NOTICE

ECA21040

• Do not depress the brake pedal when re-

moving the brake caliper.

• Be sure not to contact the sensor electrode

to any metal part when removing the rear

wheel sensor from the rear brake caliper

bracket.

3. Loosen:

•

Locknuts “1”

•

Adjusting bolts “2”

4. Remove:

•

Wheel axle nut “1”

•

Washer

•

Chain puller assembly

•

Wheel axle “2”

•

Rear wheel

•

Brake caliper bracket

NOTICE

ECA21400

Be sure to remove the rear wheel sensor be-

fore removing the brake caliper bracket, oth-

erwise the sensor could be damaged.

TIP

Push the rear wheel forward and remove the
drive chain from the rear wheel sprocket.

EAS31154

DISASSEMBLING THE REAR WHEEL

NOTICE

ECA21340

• Do not drop the wheel sensor rotor or sub-

ject it to shocks.

• If any solvent gets on the wheel sensor ro-

tor, wipe it off immediately.

1. Remove:

•

Oil seal

•

Wheel bearings
Refer to “DISASSEMBLING THE FRONT
WHEEL” on page 4-10.

1

1

1

2

1

2

Summary of Contents for MTN850-A 2017

















































































































































































































































































































































































































































































































































































Reviews:

No comments