Yamaha MTN850-A 2017 Service Manual Download Page 309

Page: 309 / 560

CRANKSHAFT AND BALANCER SHAFT

5-74

EAS31076

CHECKING THE BALANCER SHAFT

1. Measure:

•

Balancer shaft runout
Out of specification



Replace the balancer

shaft.

2. Check:

•

Balancer shaft journal surfaces

•

Bearing surfaces
Scratches/wear



Replace the balancer

shaft.

3. Measure:

•

Balancer shaft journal-to-balancer shaft bear-
ing clearance
Out of specification



Replace the balancer

shaft journal bearings.

NOTICE

ECA18400

Do not interchange the balancer shaft jour-

nal bearings. To obtain the correct balancer

shaft-journal-to-balancer shaft-journal-bear-

ing clearance and prevent engine damage,

the balancer shaft journal bearings must be

installed in their original positions.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Clean the balancer shaft journal bearings,

balancer shaft journals, and bearing portions
of the crankcase.

b. Place the upper crankcase upside down on a

bench.

c. Install the balancer shaft journal upper bear-

ings “1” and the balancer shaft into the upper
crankcase.

TIP

Align the projections “a” on the balancer shaft
journal upper bearings with the notches “b” in the
upper crankcase.

d. Put a piece of Plastigauge® “1” on each bal-

ancer shaft journal.

TIP

Do not put the Plastigauge® over the oil hole in
the balancer shaft journal.

Balancer shaft runout limit

0.030 mm (0.0012 in)

Balancer shaft journal to balancer

shaft bearing clearance

0.024–0.048 mm (0.0009–0.0019

in)

Summary of Contents for MTN850-A 2017

















































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MTN850-A 2017

Reviews:

Yamaha MTN850-A 2017, Service Manual, Page: 309 / 560

Search results

Summary of Contents for MTN850-A 2017

Reviews: