manualshive.com logo in svg

Yamaha MTN850-A 2017, Service Manual, Page: 181 / 560

Share
Download
Yamaha MTN850-A 2017 Service Manual Download Page 181

FRONT BRAKE

4-36

•

Align the end of the front brake master cylinder
holder with the punch mark “b” on the handle-
bar.

•

First, tighten the upper bolt, then the lower bolt.

•

There should be more than 11 mm (0.43 in) for
clearance between the handlebar switch (right)
and the front brake master cylinder holder. Al-
so, the punch mark should be seen.

2. Install:

•

Brake hose gaskets 

•

Brake hose

•

Brake hose union bolt

WARNING

EWA13531

Proper brake hose routing is essential to in-

sure safe vehicle operation.

TIP

•

Attach the brake hose so that its angle is 3

 to

13

 against the straight line in parallel with the

ceiling plane of the master cylinder.

•

While holding the brake hose, tighten the union
bolt as shown.

•

Turn the handlebar to the left and right to make
sure the brake hose does not touch other parts
(e.g., wire harness, cables, leads). Correct if
necessary.

3. Fill:

•

Brake master cylinder reservoir

(with the specified amount of the specified
brake fluid)

WARNING

EWA13540

• Use only the designated brake fluid. Other

brake fluids may cause the rubber seals to

deteriorate, causing leakage and poor

brake performance.

• Refill with the same type of brake fluid that

is already in the system. Mixing brake fluids

may result in a harmful chemical reaction,

leading to poor brake performance.

• When refilling, be careful that water does

not enter the brake master cylinder reser-

voir. Water will significantly lower the boil-

ing point of the brake fluid and could cause

vapor lock.

NOTICE

ECA13540

Brake fluid may damage painted surfaces

and plastic parts. Therefore, always clean up

any spilt brake fluid immediately.

4. Bleed:

•

Brake system
Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM (ABS)” on page 3-15.

5. Check:

•

Brake fluid level
Below the minimum level mark “a” 

 Add the

specified brake fluid to the proper level.
Refer to “CHECKING THE BRAKE FLUID
LEVEL” on page 3-13.

6. Check:

•

Brake lever operation
Soft or spongy feeling 

 Bleed the brake sys-

tem.
Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM (ABS)” on page 3-15.

Front brake hose union bolt

30 N·m (3.0 kgf·m, 22 lb·ft)

b

a

New

T

R

.

.

3-13

Specified brake fluid

DOT 4

a

Summary of Contents for MTN850-A 2017

















































































































































































































































































































































































































































































































































































Reviews:

No comments