manualshive.com logo in svg

Yamaha MTN850-A 2017, Service Manual, Page: 517 / 560

Share
Download
Yamaha MTN850-A 2017 Service Manual Download Page 517

ELECTRICAL COMPONENTS

8-160

charging.

TIP

Voltage should be measured 30 minutes after
the engine is stopped.

b. Connect a charger and ammeter to the bat-

tery and start charging.

TIP

Set the charging voltage to 16–17 V. If the set-
ting is lower, charging will be insufficient. If too
high, the battery will be over-charged.

c. Make sure that the current is higher than the

standard charging current written on the bat-
tery.

TIP

If the current is lower than the standard charging
current written on the battery, set the charging
voltage adjust dial at 20–24 V and monitor the
amperage for 3–5 minutes to check the battery.

d. Adjust the voltage so that the current is at the

standard charging level.

e. Set the time according to the charging time

suitable for the open-circuit voltage.

f. If charging requires more than 5 hours, it is

advisable to check the charging current after
a lapse of 5 hours. If there is any change in
the amperage, readjust the voltage to obtain
the standard charging current.

g. Measure the battery open-circuit voltage after

leaving the battery unused for more than 30
minutes.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

Charging method using a constant voltage

charger

a. Measure the open-circuit voltage prior to

charging.

TIP

Voltage should be measured 30 minutes after
the engine is stopped.

b. Connect a charger and ammeter to the bat-

tery and start charging.

c. Make sure that the current is higher than the

standard charging current written on the bat-

tery.

TIP

If the current is lower than the standard charging
current written on the battery, this type of battery
charger cannot charge the VRLA (Valve Regu-
lated Lead Acid) battery. A variable voltage
charger is recommended.

d. Charge the battery until the battery’s charg-

ing voltage is 15 V.

TIP

Set the charging time at 20 hours (maximum).

e. Measure the battery open-circuit voltage after

leaving the battery unused for more than 30
minutes.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

6. Install:

•

Battery
Refer to “GENERAL CHASSIS (1)” on page
4-1.

7. Connect:

•

Battery leads
(to the battery terminals)

NOTICE

ECA13630

First, connect the positive battery lead “1”,

and then the negative battery lead “2”.

8. Check:

•

Battery terminals
Dirt 

 Clean with a wire brush.

Loose connection 

 Connect properly.

9. Lubricate:

•

Battery terminals

•

Standard charging current is reached

Battery is good.

•

Standard charging current is not reached

Replace the battery.

12.8 V or more --- Charging is complete.

12.7 V or less --- Recharging is required.

Under 12.0 V --- Replace the battery.

12.8 V or more --- Charging is complete.

12.7 V or less --- Recharging is required.

Under 12.0 V --- Replace the battery.

Recommended lubricant

Dielectric grease

1

2

Summary of Contents for MTN850-A 2017

















































































































































































































































































































































































































































































































































































Reviews:

No comments