Yamaha MTN850-A 2017 Service Manual Download Page 337

Page: 337 / 560

FUEL TANK

7-4

EAS30456

INSTALLING THE FUEL PUMP

1. Install:

•

Fuel pump gasket

•

Fuel pump

•

Fuel pump bracket

•

Fuel pump bolts

TIP

•

Do not damage the installation surfaces of the
fuel tank when installing the fuel pump.

•

Always use a new fuel pump gasket.

•

Install the fuel pump gasket so that the lip side
turns to the inside of the fuel tank.

•

Install the fuel pump as shown in the illustra-
tion.

•

Align the projection “a” on the fuel pump with
the slot in the fuel pump bracket.

•

Tighten the fuel pump bolts in the proper tight-
ening sequence as shown.

EAS30457

INSTALLING THE FUEL TANK

1. Connect:

•

Fuel hose (fuel tank side)

NOTICE

ECA17500

When installing the fuel hose, make sure that

it is securely connected, and that the fuel

hose connector cover on the fuel hose is in

the correct position, otherwise the fuel hose

will not be properly installed.

TIP

•

Install the fuel hose onto the fuel pump secure-
ly, and slide the fuel hose connector cover “1”
in the direction shown in the illustration.

•

It is prohibited to wear the cotton work gloves
or equivalent coverings.

2. Connect:

•

Fuel tank breather hose

•

Fuel tank drain hose

•

Fuel pump coupler

Fuel pump bolt

4.0 N·m (0.40 kgf·m, 2.9 lb·ft)

A. Forward

New

Summary of Contents for MTN850-A 2017

















































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MTN850-A 2017

Reviews:

Yamaha MTN850-A 2017, Service Manual, Page: 337 / 560

Search results

Summary of Contents for MTN850-A 2017

Reviews: