manualshive.com logo in svg

Yamaha MTN850-A 2017, Service Manual, Page: 138 / 560

Share
Download
Yamaha MTN850-A 2017 Service Manual Download Page 138

PERIODIC MAINTENANCE

3-28

5. Remove:

•

Water pump drain bolt “1”

•

Copper washer “2”

6. Drain:

•

Coolant
(from the engine and radiator)

7. Install:

•

Water pump drain bolt

•

Copper washer 

8. Install:

•

Collars

•

Coolant reservoir

•

Coolant reservoir cover

•

Coolant reservoir bolt

9. Fill:

•

Cooling system
(with the specified amount of the recom-
mended coolant)

Handling notes for coolant
Coolant is potentially harmful and should be
handled with special care.

WARNING

EWA13040

• If coolant splashes in your eyes, thorough-

ly wash them with water and consult a doc-

tor.

• If coolant splashes on your clothes, quickly

wash it away with water and then with soap

and water.

• If coolant is swallowed, induce vomiting

and get immediate medical attention.

NOTICE

ECA21291

• Adding water instead of coolant dilutes the

antifreeze concentration of the coolant. If

water is used instead of coolant; check,

and if necessary, correct the antifreeze

concentration of the coolant.

• Use only distilled water. However, if dis-

tilled water is not available, soft water may

be used.

• If coolant comes into contact with painted

surfaces, immediately wash them with wa-

ter.

• Do not mix different types of antifreeze.

10.Install:

•

Radiator cap stopper

•

Radiator cap

•

Radiator cap bolt

11.Fill:

•

Coolant reservoir
(with the recommended coolant to the maxi-
mum level mark “a”)

12.Install:

•

Coolant reservoir cap

13.Start the engine, warm it up for several min-

utes, and then turn it off.

14.Check:

•

Coolant level
Refer to “CHECKING THE COOLANT LEV-

Water pump drain bolt

10 N·m (1.0 kgf·m, 7.2 lb·ft)

Coolant reservoir bolt

0.5 N·m (0.05 kgf·m, 0.36 lb·ft)

Coolant reservoir bolt

9 N·m (0.9 kgf·m, 6.5 lb·ft)

Recommended antifreeze

High-quality ethylene glycol anti-

freeze containing corrosion 

inhibitors for aluminum engines 

Mixing ratio

1:1 (antifreeze:water)

Radiator (including all routes)

1.93 L (2.04 US qt, 1.70 Imp.qt)

Coolant reservoir (up to the maxi-

mum level mark)

0.25 L (0.26 US qt, 0.22 Imp.qt)

1

2

New

T

R

.

.

T

R

.

.

Radiator cap bolt

5 N·m (0.5 kgf·m, 3.6 lb·ft)

T

R

.

.

a

Summary of Contents for MTN850-A 2017

















































































































































































































































































































































































































































































































































































Reviews:

No comments