Home
/
Yamaha
/
MTN850-A 2017
/
Service Manual

Yamaha MTN850-A 2017, Service Manual, Page: 114 / 560

Share

Page: 114 / 560

Yamaha MTN850-A 2017 Service Manual Download Page 114

PERIODIC MAINTENANCE

3-4

EAS32024

CHECKING THE VEHICLE USING THE

YAMAHA DIAGNOSTIC TOOL

Use the Yamaha diagnostic tool and check the
vehicle according to the following procedure.
1. Remove:

•

Rider seat
Refer to “GENERAL CHASSIS (1)” on page
4-1.

2. Remove the protective cap “1”, and then con-

nect the Yamaha diagnostic tool to the cou-
pler.

3. Check:

•

Fault codes

TIP

Use the “Diagnosis of malfunction” function of
the Yamaha diagnostic tool to check the fault
codes. For information about using the Yamaha
diagnostic tool, refer to the operation manual
that is included with the tool.

Fault code number is displayed



Check and

repair the probable cause of the malfunction.
Refer to “TROUBLESHOOTING DETAILS
(FAULT CODE)” on page 8-37.

4. Perform:

•

Dynamic inspection

TIP

Use the “Dynamic inspection” function of the
Yamaha diagnostic tool version 3.0 and after to
perform the dynamic inspection. For information
about using the Yamaha diagnostic tool, refer to
the operation manual that is included with the
tool.

5. Install:

•

Rider seat
Refer to “GENERAL CHASSIS (1)” on page
4-1.

EAS30619

CHECKING THE FUEL LINE

The following procedure applies to all of the fuel,
drain and breather hoses.
1. Remove:

•

Air scoop
Refer to “GENERAL CHASSIS (1)” on page
4-1.

•

Rider seat
Refer to “GENERAL CHASSIS (1)” on page
4-1.

•

Fuel tank cover
Refer to “GENERAL CHASSIS (1)” on page
4-1.

•

Fuel tank
Refer to “FUEL TANK” on page 7-1.

2. Check:

•

Fuel hose “1”

•

Fuel tank breather hose “2”

•

Fuel tank drain hose “3”
Cracks/damage



Replace.

Loose connection



Connect properly.

NOTICE

ECA14940

Make sure the fuel tank breather hose is rout-

ed correctly.

TIP

Before removing the fuel hoses, place a few
rags in the area under where it will be removed.

3. Install:

•

Fuel tank
Refer to “FUEL TANK” on page 7-1.

•

Fuel tank cover
Refer to “GENERAL CHASSIS (1)” on page
4-1.

•

Rider seat
Refer to “GENERAL CHASSIS (1)” on page
4-1.

•

Air scoop
Refer to “GENERAL CHASSIS (1)” on page
4-1.

Yamaha diagnostic tool USB

90890-03250

Yamaha diagnostic tool (A/I)

90890-03252

1

1

2

3

«
...
112
113
114
115
116
...
»

Summary of Contents for MTN850-A 2017

















































































































































































































































































































































































































































































































































































Reviews:

No comments