manualshive.com logo in svg

Yamaha MTN850-A 2017, Service Manual, Page: 118 / 560

Share
Download
Yamaha MTN850-A 2017 Service Manual Download Page 118

PERIODIC MAINTENANCE

3-8

the following table, and then select the suit-
able valve pad.

TIP

Refer to the following table for the available
valve pads.

Example:
Valve pad number = 163
Rounded value = 165
New valve pad number = 165

f. Install the new valve pad “1” and the valve lift-

er “2”.

TIP

•

Lubricate the valve pad with molybdenum di-
sulfide oil.

•

Lubricate the valve lifter (Top side) with molyb-
denum disulfide oil.

•

Lubricate the valve lifter (Outer side) with en-
gine oil.

•

Install the valve lifter and the valve pad in the
correct place.

•

The valve lifter must turn smoothly when rotat-
ed by hand.

g. Install the exhaust and intake camshafts, tim-

ing chain and camshaft caps.

TIP

•

Refer to “CAMSHAFTS” on page 5-9.

•

Lubricate the camshaft lobes and camshaft
journals.

•

First, install the exhaust camshaft.

•

Align the camshafts marks with the camshaft
cap marks.

•

Turn the crankshaft counterclockwise several
full turns to seat the parts.

h. Measure the valve clearance again.
i. If the valve clearance is still out of specifica-

tion, repeat all of the valve clearance adjust-
ment steps until the specified clearance is
obtained.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

7. Install:

•

All removed parts

TIP

For installation, reverse the removal procedure.

EAS31017

CHECKING THE ENGINE IDLING SPEED

TIP

Prior to checking the engine idling speed, the
throttle body synchronization should be adjusted
properly, the air filter element should be clean,
and the engine should have adequate compres-
sion.

1. Start the engine and let it warm up for several

minutes.

2. Check:

•

Engine idling speed
Out of specification 

 Go to next step.

3. Check:

•

ISC (idle speed control) learning value
“00” or “01” 

 Check the intake system.

“02” 

 Clean the throttle bodies.

Refer to “CHECKING AND CLEANING THE
THROTTLE BODIES” on page 7-8.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect the Yamaha diagnostic tool. 

Use the diagnostic code number “67”.
Refer to “SELF-DIAGNOSTIC FUNCTION
AND DIAGNOSTIC CODE TABLE” on page
9-5.

b. Check the ISC (idle speed control) leaning

value.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

Last digit

Rounded value

0, 1, 2

0

3, 4, 5, 6

5

7, 8, 9

10

Valve pad range

Nos. 150–240

Valve pad thickness

1.50–2.40 mm 

(0.0590–0.0944 in)

Available valve pads

25 thicknesses in 0.05 

mm (0.002 in) incre-

ments

Camshaft cap bolt

10 N·m (1.0 kgf·m, 7.2 lb·ft)

T

R

.

.

Engine idling speed

1100–1300 r/min

Summary of Contents for MTN850-A 2017

















































































































































































































































































































































































































































































































































































Reviews:

No comments