manualshive.com logo in svg

Yamaha MTN850-A 2017, Service Manual, Page: 139 / 560

Share
Download
Yamaha MTN850-A 2017 Service Manual Download Page 139

PERIODIC MAINTENANCE

3-29

EL” on page 3-26.

TIP

Before checking the coolant level, wait a few
minutes until the coolant has settled.

EAS30814

CHECKING THE FRONT BRAKE LIGHT 

SWITCH

Refer to “ELECTRICAL COMPONENTS” on
page 8-149.

EAS30659

ADJUSTING THE REAR BRAKE LIGHT 

SWITCH

TIP

The rear brake light switch is operated by move-
ment of the brake pedal. The rear brake light
switch is properly adjusted when the brake light
comes on just before the braking effect starts.

1. Check:

•

Rear brake light operation timing
Incorrect 

 Adjust.

2. Adjust:

•

Rear brake light operation timing

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Hold the main body “1” of the rear brake light

switch so that it does not rotate and turn the
adjusting nut “2” in direction “a” or “b” until the
rear brake light comes on at the proper time.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS30660

CHECKING AND LUBRICATING THE 

CABLES

The following procedure applies to all of the in-
ner and outer cables.

WARNING

EWA13270

Damaged outer cable may cause the cable to

corrode and interfere with its movement. Re-

place damaged outer cable and inner cables

as soon as possible.

1. Check:

•

Outer cable
Damage 

 Replace.

2. Check:

•

Cable operation
Rough movement 

 Lubricate.

TIP

Hold the cable end upright and pour a few drops
of lubricant into the cable sheath or use a suit-
able lubricating device.

EAS30815

CHECKING THE THROTTLE GRIP

1. Check:

•

Throttle cables
Damage/deterioration 

 Replace.

•

Throttle cable installation
Incorrect 

 Reinstall the throttle cables.

Refer to “HANDLEBAR” on page 4-58.

2. Check:

•

Throttle grip movement
Rough movement 

 Lubricate or replace the

defective part(s).

TIP

With the engine stopped, turn the throttle grip
slowly and release it. Make sure that the throttle
grip turns smoothly and returns properly when
released. 
Repeat this check with the handlebar turned all
the way to the left and right.

3. Check:

•

Throttle grip free play “a”
Out of specification 

 Adjust.

Direction “a”

Brake light comes on sooner.

Direction “b”

Brake light comes on later.

2

1

a

b

Recommended lubricant

Engine oil or a suitable cable lu-

bricant

Recommended lubricant

Suitable cable lubricant

Throttle grip free play

3.0–5.0 mm (0.12–0.20 in)

Summary of Contents for MTN850-A 2017

















































































































































































































































































































































































































































































































































































Reviews:

No comments