manualshive.com logo in svg

Yamaha MTN850-A 2017, Service Manual, Page: 410 / 560

Share
Download
Yamaha MTN850-A 2017 Service Manual Download Page 410

FUEL INJECTION SYSTEM

8-53

3-4

[For P0123] Open circuit

Between throttle position sensor coupler and ECU coupler: white–white

If there is no continuity, replace the wire harness.

3-5

[For P0222] Ground short circuit

Between throttle position sensor coupler and ground: black–ground

If there is continuity, replace the wire harness.

3-6

[For P0223] Open circuit

Between throttle position sensor coupler and ECU coupler: black–black

If there is no continuity, replace the wire harness.

Fault code No.

P0122, P0123, P0222, P0223, P2135

Item

[P0122] Throttle position sensor: ground short circuit detected.

[P0123] Throttle position sensor: open or power short circuit 

detected.

[P0222] Throttle position sensor: ground short circuit detected.

[P0223] Throttle position sensor: open or power short circuit 

detected.

[P2135] Throttle position sensor: output voltage deviation error.

Summary of Contents for MTN850-A 2017

















































































































































































































































































































































































































































































































































































Reviews:

No comments