Yamaha MTN850-A 2017 Service Manual Download Page 210

Page: 210 / 560

FRONT FORK

4-65

•

Oil seal clip “2”
(with a flat-head screwdriver)

NOTICE

ECA19100

Do not scratch the outer tube.

4. Remove:

•

Outer tube

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Hold the front fork leg horizontally.
b. Securely clamp the brake caliper bracket in a

vise with soft jaws.

c. Separate the outer tube from the inner tube

by pulling the outer tube forcefully but careful-
ly.

NOTICE

ECA19880

Excessive force will damage the bushings.

Damaged bushings must be replaced.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

5. Remove:

•

Damper rod assembly bolt

•

Damper rod assembly

TIP

While holding the damper rod with the damper
rod holder “1”, loosen the damper rod assembly
bolt.

EAS30208

CHECKING THE FRONT FORK LEGS

The following procedure applies to both of the
front fork legs.
1. Check:

•

Inner tube “1”

•

Outer tube “2”
Bends/damage/scratches



Replace.

WARNING

EWA13650

Do not attempt to straighten a bent inner

tube as this may dangerously weaken it.

2. Measure:

•

Fork spring free length “a”
Out of specification



Replace.

Damper rod holder (ø27)

90890-01582

Damper rod holder

YM-01582

Fork spring free length

300.3 mm (11.82 in)

Limit

294.2 mm (11.59 in)

Summary of Contents for MTN850-A 2017

















































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MTN850-A 2017

Reviews:

Yamaha MTN850-A 2017, Service Manual, Page: 210 / 560

Search results

Summary of Contents for MTN850-A 2017

Reviews: