Yamaha MTN850-A 2017 Service Manual Download Page 346

Page: 346 / 560

THROTTLE BODIES

7-13

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS30486

ADJUSTING THE ACCELERATOR POSITION

SENSOR

WARNING

EWA15960

• Handle the accelerator position sensor with

special care.

• Never subject the accelerator position sen-

sor to strong shocks. If the accelerator po-

sition sensor is dropped, replace it.

1. Check:

•

Accelerator position sensor
Refer to “CHECKING THE ACCELERATOR
POSITION SENSOR” on page 8-170.

2. Adjust:

•

Accelerator position sensor angle

TIP

Before adjusting the accelerator position sensor,
the throttle bodies must be removed.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Temporary tighten the accelerator position

sensor bolts.

b. Check that the throttle valves are fully closed.
c. Connect the accelerator position sensor to

the wire harness.

d. Connect the throttle cables to the throttle bod-

ies.

e. Remove the protective cap “1”, and then con-

nect the Yamaha diagnostic tool to coupler.

TIP

For information about using the Yamaha diag-
nostic tool, refer to the operation manual that is
included with the tool.

f. Diagnostic code number “14” is selected.
g. Turn the throttle grip to the fully closed posi-

tion.

h. Adjust the position of the accelerator position

sensor angle so that 12–22 can appear in the
Yamaha diagnostic tool screen.

i. After adjusting the accelerator position sen-

sor angle, tighten the accelerator position
sensor bolts “2”.

j. Turn the throttle grip to the fully open position.
k. Check the Yamaha diagnostic tool screen

value. If the Yamaha diagnostic tool screen
value is not 97–107, adjust the accelerator
position sensor angle.

l. Select the diagnostic code number “15”.
m. Turn the throttle grip to the fully closed posi-

tion.

n. Check the Yamaha diagnostic tool screen

value. If the Yamaha diagnostic tool screen
value is not 10–24, adjust the accelerator po-
sition sensor angle.

o. Turn the throttle grip to the fully open position.
p. Check the Yamaha diagnostic tool screen

value. If the Yamaha diagnostic tool screen
value is not 95–109, adjust the accelerator
position sensor angle.

q. Repeat steps (f) to (p) until the Yamaha diag-

nostic tool screen values are within the spec-
ified ranges.

Accelerator position sensor bolt

3.5 N·m (0.35 kgf·m, 2.5 lb·ft)

Summary of Contents for MTN850-A 2017

















































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MTN850-A 2017

Reviews:

Yamaha MTN850-A 2017, Service Manual, Page: 346 / 560

Search results

Summary of Contents for MTN850-A 2017

Reviews: