manualshive.com logo in svg

Yamaha MTN850-A 2017, Service Manual, Page: 178 / 560

Share
Download
Yamaha MTN850-A 2017 Service Manual Download Page 178

FRONT BRAKE

4-33

EAS30172

DISASSEMBLING THE FRONT BRAKE 

CALIPERS

The following procedure applies to both of the
brake calipers.
1. Remove:

•

Brake caliper pistons “1”

•

Brake caliper piston dust seals “2”

•

Brake caliper piston seals “3”

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Secure the right side brake caliper pistons

with a piece of wood “a”.

b. Blow compressed air into the brake hose joint

opening “b” to force out the left side pistons
from the brake caliper.

WARNING

EWA17060

• Never try to pry out the brake caliper pis-

tons.

• Do not loosen the bolts “4”.

c. Remove the brake caliper piston dust seals

and brake caliper piston seals.

d. Repeat the previous steps to force out the

right side pistons from the brake caliper.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS30173

CHECKING THE FRONT BRAKE CALIPERS

The following procedure applies to both of the
brake calipers.

1. Check:

•

Brake caliper pistons “1”
Rust/scratches/wear 

 Replace the brake

caliper pistons.

•

Brake caliper cylinders “2”
Scratches/wear 

 Replace the brake caliper

assembly.

•

Brake caliper body “3”
Cracks/damage 

 Replace the brake caliper

assembly.

•

Brake fluid delivery passages
(brake caliper body)
Obstruction 

 Blow out with compressed air.

WARNING

EWA13611

Whenever a brake caliper is disassembled,

replace the brake caliper piston dust seals

and brake caliper piston seals.

EAS30174

ASSEMBLING THE FRONT BRAKE 

CALIPERS

WARNING

EWA16560

• Before installation, all internal brake com-

ponents should be cleaned and lubricated

with clean or new brake fluid.

• Never use solvents on internal brake com-

ponents as they will cause the brake caliper

piston dust seals and brake caliper piston

seals to swell and distort.

• Whenever a brake caliper is disassembled,

1

2

2

1

3

3

b

4

a

Recommended brake component 

replacement schedule

Brake pads

If necessary

Piston seals

Every two years

Piston dust seals

Every two years

Brake hoses

Every four years

Brake fluid

Every two years and 

whenever the brake is 

disassembled

1

1

2

3

Summary of Contents for MTN850-A 2017

















































































































































































































































































































































































































































































































































































Reviews:

No comments