Yamaha GRIZZLY 700 FI YFM7FGPX Page 56 Owner'S Manual Download

Page: 56 / 164

6-3

NOTE:

Make sure that the drive select lever is completely
shifted into position.

3. Release the brake pedal, and then open the

throttle lever gradually.

Shifting: Neutral to Reverse and Reverse to
Park

NOTE:

The drive select lever cannot be shifted into or from
reverse or park without applying the brake pedal.

1. Bring the ATV to a complete stop.
2. Apply the brake pedal.
3. Shift from neutral to reverse or from reverse to

park and vice versa by moving the drive select
lever along the shift guide.

1. Drive select lever

2. L (Low-range)

3. H (High-range)
4. N (Neutral)

5. R (Reverse)

6. P (Park)

U3B462E0.book Page 3 Tuesday, March 20, 2007 11:46 AM

Summary of Contents for GRIZZLY 700 FI YFM7FGPX





































































































































































Search results

Summary of Contents for GRIZZLY 700 FI YFM7FGPX

Reviews:

Related manuals for GRIZZLY 700 FI YFM7FGPX

Brands by name

Popular brands

Yamaha GRIZZLY 700 FI YFM7FGPX, Owner'S Manual

Search results

Summary of Contents for GRIZZLY 700 FI YFM7FGPX

Reviews:

Related manuals for GRIZZLY 700 FI YFM7FGPX

Brands by name

Popular brands