manualshive.com logo in svg

Yamaha GRIZZLY 700 FI YFM7FGPX, Owner'S Manual

Share
Download
Yamaha GRIZZLY 700 FI YFM7FGPX Owner'S Manual Download Page 124

8-39

8

CAUTION:

ECB00440

Do not twist the sponge material when squeez-
ing it.

7. Check the sponge material and replace it if

damaged.

8. Apply Yamaha foam air filter oil or other qual-

ity foam air filter oil to the sponge material.

NOTE:

The sponge material should be wet but not drip-
ping.

9. Install the mesh and the sponge material into

the air filter case.

10. Insert the projections on the air filter case cov-

er into the holders on the air filter case, and
then install the air filter case cover by hooking
the holders onto the cover.

11. Install the panel.

NOTE:

The air filter element should be cleaned every 20–
40 hours. It should be cleaned and lubricated more
often if the ATV is operated in extremely dusty ar-
eas. Each time the air filter element maintenance
is performed, check the air inlet of the air filter case
for obstructions. Check the air filter case rubber
joint to the throttle body and the rubber joint mani-

U3B462E0.book  Page 39  Tuesday, March 20, 2007  11:46 AM

Summary of Contents for GRIZZLY 700 FI YFM7FGPX





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands