Yamaha GRIZZLY 700 FI YFM7FGPX Owner'S Manual Download

Page: 52 / 164

5-6

Minimum tire pressure:

Front:

32.0 kPa (4.6 psi) (0.320 kgf/cm²)

Rear:

27.0 kPa (3.9 psi) (0.270 kgf/cm²)

• Use no more than the following pressures

when seating the tire beads.

Maximum tire seating pressure:

Front:

250 kPa (36 psi) (2.5 kgf/cm²)

Rear:

250 kPa (36 psi) (2.5 kgf/cm²)

Higher pressures and fast inflation may
cause a tire to burst. Inflate the tires very
slowly and carefully.

EBU19820

Measuring the tire pressure

Use the low-pressure tire gauge.

NOTE:

The low-pressure tire gauge is included as stan-
dard equipment. Make two measurements of the
tire pressure and use the second reading. Dust or
dirt in the gauge could cause the first reading to be
incorrect.

Set the tire pressure when the tires are cold. Set
the tire pressures to the following specifications:

1. Low-pressure tire gauge

U3B462E0.book Page 6 Tuesday, March 20, 2007 11:46 AM

Summary of Contents for GRIZZLY 700 FI YFM7FGPX





































































































































































Search results

Summary of Contents for GRIZZLY 700 FI YFM7FGPX

Reviews:

Related manuals for GRIZZLY 700 FI YFM7FGPX

Brands by name

Popular brands

Yamaha GRIZZLY 700 FI YFM7FGPX, Owner'S Manual

Search results

Summary of Contents for GRIZZLY 700 FI YFM7FGPX

Reviews:

Related manuals for GRIZZLY 700 FI YFM7FGPX

Brands by name

Popular brands