Yamaha GRIZZLY 700 FI YFM7FGPX Owner'S Manual Download

Page: 53 / 164

5-7

EBU19830

Tire wear limit

Replace the tire when the tire groove decreases to
3 mm (0.12 in).

EBU19840

Chassis fasteners

Make sure that all nuts, bolts and screws are prop-
erly tightened.

EBU19850

Instruments, lights and switches

Check that all instruments, lights and switches are
working properly. Correct if necessary.

Recommended pressure:

Front

35.0 kPa (5.0 psi) (0.350 kgf/cm²)

Rear

30.0 kPa (4.3 psi) (0.300 kgf/cm²)

Minimum:

Front

32.0 kPa (4.6 psi) (0.320 kgf/cm²)

Rear

27.0 kPa (3.9 psi) (0.270 kgf/cm²)

Maximum:

Front

38.0 kPa (5.5 psi) (0.380 kgf/cm²)

Rear

33.0 kPa (4.8 psi) (0.330 kgf/cm²)

1. Tire wear limit

U3B462E0.book Page 7 Tuesday, March 20, 2007 11:46 AM

Summary of Contents for GRIZZLY 700 FI YFM7FGPX





































































































































































Search results

Summary of Contents for GRIZZLY 700 FI YFM7FGPX

Reviews:

Related manuals for GRIZZLY 700 FI YFM7FGPX

Brands by name

Popular brands

Yamaha GRIZZLY 700 FI YFM7FGPX, Owner'S Manual

Search results

Summary of Contents for GRIZZLY 700 FI YFM7FGPX

Reviews:

Related manuals for GRIZZLY 700 FI YFM7FGPX

Brands by name

Popular brands