manualshive.com logo in svg

Yamaha GRIZZLY 700 FI YFM7FGPX, Owner'S Manual

Share
Download
Yamaha GRIZZLY 700 FI YFM7FGPX Owner'S Manual Download Page 153

9-3

9

e. Remove the spark plug cap from the spark

plug, and then install the spark plug and
the spark plug cap.

4. Lubricate all control cables and the pivoting

points of all levers and pedals.

5. Check and, if necessary, correct the tire air

pressure, and then block up the ATV so that
all of its wheels are off the ground. Alternative-
ly, turn the wheels a little every month in order
to prevent the tires from becoming degraded
in one spot.

6. Cover the muffler outlet with a plastic bag to

prevent moisture from entering it.

7. Remove the battery and fully charge it. Store

it in a cool, dry place and charge it once a
month. Do not store the battery in an exces-
sively cold or warm place [less than 0 °C (30
°F) or more than 30 °C (90 °F)]. For more in-
formation on storing the battery, see page
8-54.

NOTE:

Make any necessary repairs before storing the
ATV.

U3B462E0.book  Page 3  Tuesday, March 20, 2007  11:46 AM

Summary of Contents for GRIZZLY 700 FI YFM7FGPX





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands