Yamaha GRIZZLY 700 FI YFM7FGPX Page 46 Owner'S Manual Download

Page: 46 / 164

4-23

4. When the auxiliary DC jack is not being used,

cover it with the cap.

CAUTION:

ECB00120

●

Do not use accessories requiring more than
the above maximum capacity. This may
overload the circuit and cause the fuse to
blow.

●

If accessories are used without the engine
running or with the headlights turned on, the
battery will lose its charge and engine start-
ing may become difficult.

●

Do not use an automotive cigarette lighter or
other accessories with a plug that gets hot
because the jack can be damaged.

1. Auxiliary DC jack cap

1. Auxiliary DC jack

Maximum rated capacity for the auxiliary DC
jack:

DC 12 V, 120 W (10 A)

U3B462E0.book Page 23 Tuesday, March 20, 2007 11:46 AM

Summary of Contents for GRIZZLY 700 FI YFM7FGPX





































































































































































Search results

Summary of Contents for GRIZZLY 700 FI YFM7FGPX

Reviews:

Related manuals for GRIZZLY 700 FI YFM7FGPX

Brands by name

Popular brands

Yamaha GRIZZLY 700 FI YFM7FGPX, Owner'S Manual

Search results

Summary of Contents for GRIZZLY 700 FI YFM7FGPX

Reviews:

Related manuals for GRIZZLY 700 FI YFM7FGPX

Brands by name

Popular brands