Yamaha GRIZZLY 700 FI YFM7FGPX Page 147 Owner'S Manual Download

Page: 147 / 164

8-62

4. Insert a new bulb into the bulb holder, push it

in, and then turn it clockwise until it stops.

5. Install the bulb holder (together with the bulb)

by turning it clockwise.

6. Install the panel.

EBU25650

Removing a wheel

1. Loosen the wheel nuts.

2. Elevate the ATV and place a suitable stand

under the frame.

3. Remove the nuts from the wheel.
4. Remove the wheel.

EBU25700

Installing a wheel

1. Install the wheel and the nuts.

NOTE:

●

The arrow mark

on the tire must point toward

the rotating direction of the wheel.

●

Tapered nuts are used for both the front and rear
wheels. Install the nuts with their tapered side to-
wards the wheel.

1. Wheel nut

1. Arrow mark

U3B462E0.book Page 62 Tuesday, March 20, 2007 11:46 AM

Summary of Contents for GRIZZLY 700 FI YFM7FGPX





































































































































































Search results

Summary of Contents for GRIZZLY 700 FI YFM7FGPX

Reviews:

Related manuals for GRIZZLY 700 FI YFM7FGPX

Brands by name

Popular brands

Yamaha GRIZZLY 700 FI YFM7FGPX, Owner'S Manual

Search results

Summary of Contents for GRIZZLY 700 FI YFM7FGPX

Reviews:

Related manuals for GRIZZLY 700 FI YFM7FGPX

Brands by name

Popular brands