Yamaha GRIZZLY 700 FI YFM7FGPX Owner'S Manual Download

Page: 109 / 164

8-24

NOTE:

Skip steps 5–9 if the oil filter cartridge is not being
replaced.

5. Remove panel G. (See page 8-8.)
6. Remove the oil filter cartridge with an oil filter

wrench.

NOTE:

An oil filter wrench is available at a nearby Yamaha
dealer.

7. Apply a thin coat of engine oil to the O-ring of

the new oil filter cartridge.

NOTE:

Make sure that the O-ring is properly seated.

8. Install the new oil filter cartridge with an oil fil-

ter wrench, and then tighten it to the specified
torque with a torque wrench.

1. Oil filter cartridge

2. Oil filter wrench

1. O-ring

U3B462E0.book Page 24 Tuesday, March 20, 2007 11:46 AM

Summary of Contents for GRIZZLY 700 FI YFM7FGPX





































































































































































Search results

Summary of Contents for GRIZZLY 700 FI YFM7FGPX

Reviews:

Related manuals for GRIZZLY 700 FI YFM7FGPX

Brands by name

Popular brands

Yamaha GRIZZLY 700 FI YFM7FGPX, Owner'S Manual

Search results

Summary of Contents for GRIZZLY 700 FI YFM7FGPX

Reviews:

Related manuals for GRIZZLY 700 FI YFM7FGPX

Brands by name

Popular brands