Yamaha GRIZZLY 700 FI YFM7FGPX Owner'S Manual Download Page 134

Page: 134 / 164

8-49

Replacement of brake components requires
professional knowledge. These procedures
should be performed by a Yamaha dealer.

EBU27780

Adjusting the brake pedal free play and
checking the brake pedal position

The brake pedal free play must be adjusted and
brake pedal position must be checked and, if nec-
essary, adjusted at the intervals specified in the
periodic maintenance and lubrication chart.

NOTE:

●

Always perform this maintenance completely in
the following order whenever adjusting the rear
brake.

●

Before adjusting the brake pedal free play and
checking the brake pedal position, check the
rear brake pads for wear.

Adjusting the brake pedal free play

The brake pedal free play should measure 0.0–5.0
mm (0.00–0.20 in) as shown. If the free play is in-
correct, adjust it as follows.

1. Remove panel H. (See page 8-8.)
2. Loosen the locknut.
3. Turn the brake pedal free play adjusting nut in

direction (a) to increase the free play, and in
direction (b) to decrease it.

1. Brake pedal free play

U3B462E0.book Page 49 Tuesday, March 20, 2007 11:46 AM

Summary of Contents for GRIZZLY 700 FI YFM7FGPX





































































































































































Search results

Summary of Contents for GRIZZLY 700 FI YFM7FGPX

Reviews:

Brands by name

Popular brands

Yamaha GRIZZLY 700 FI YFM7FGPX, Owner'S Manual

Search results

Summary of Contents for GRIZZLY 700 FI YFM7FGPX

Reviews:

Brands by name

Popular brands