Yamaha GRIZZLY 700 FI YFM7FGPX Page 135 Owner'S Manual Download

Page: 135 / 164

8-50

4. Tighten the locknut.
5. Install the panel.

If the correct free play cannot be obtained, have a
Yamaha dealer adjust it.

NOTE:

When adjusting the rear brake pedal free play:

●

Be sure not to step on the brake pedal.

●

Make sure the rear brake lever and brake pedal
do not move.

Checking the brake pedal position

The top of the brake pedal should be positioned
56.7 mm (2.23 in) above the top of the footrest. If
the brake pedal position is incorrect, have a
Yamaha dealer adjust it.

WARNING

EWB02070

Operating with improperly serviced or adjust-
ed brakes could cause loss of braking ability,
which could lead to an accident.
After servicing:

●

Make sure the brakes operate smoothly and
that the free play is correct.

●

Make sure the brakes do not drag.

1. Locknut
2. Brake pedal free play adjusting nut

1. Distance between brake pedal and footrest

U3B462E0.book Page 50 Tuesday, March 20, 2007 11:46 AM

Summary of Contents for GRIZZLY 700 FI YFM7FGPX





































































































































































Search results

Summary of Contents for GRIZZLY 700 FI YFM7FGPX

Reviews:

Related manuals for GRIZZLY 700 FI YFM7FGPX

Brands by name

Popular brands

Yamaha GRIZZLY 700 FI YFM7FGPX, Owner'S Manual

Search results

Summary of Contents for GRIZZLY 700 FI YFM7FGPX

Reviews:

Related manuals for GRIZZLY 700 FI YFM7FGPX

Brands by name

Popular brands