manualshive.com logo in svg

Yamaha GRIZZLY 700 FI YFM7FGPX, Owner'S Manual

The Yamaha GRIZZLY 700 FI YFM7FGPX is a powerful and reliable all-terrain vehicle, perfect for outdoor enthusiasts. With its user-friendly features and cutting-edge technology, this machine delivers exceptional performance. To explore its full potential, make sure to download the free Owner's Manual from manualshive.com for step-by-step instructions and valuable information.

Share
Download
background image

8-36

8

18. When coolant begins to flow out of the bolt

hole, tighten the cylinder head air bleed bolt to
the specified torque.

19. Start the engine and let it idle for ten minutes.
20. Rev the engine five times.
21. Pour the recommended coolant into the radia-

tor until it is full.

22. Stop the engine and allow it to cool. If the cool-

ant level has dropped after the engine has
cooled, add sufficient coolant until it reaches
the top of the radiator, and then install the ra-
diator cap.

23. Start the engine, and then check for coolant

leakage.

NOTE:

If any leakage is found, have a Yamaha dealer
check the cooling system.

24. Install the V-belt cooling duct, and then tighten

the clamp screw.

25. Install the panels.

EBU27801

Cleaning the air filter element 

The air filter element should be cleaned at the in-
tervals specified in the periodic maintenance and
lubrication chart. Clean the air filter element more
frequently if you are riding in unusually wet or dusty
areas.

NOTE:

There are two check hoses at the bottom of the air
filter case, which are located behind panels D and
E. (See page 8-8 for an explanation on removing

1. Cylinder head air bleed bolt

Tightening torque:

Cylinder head air bleed bolt:

10 Nm (1.0 m·kgf, 7.2 ft·lbf)

U3B462E0.book  Page 36  Tuesday, March 20, 2007  11:46 AM

Summary of Contents for GRIZZLY 700 FI YFM7FGPX





































































































































































Reviews:

No comments

Related manuals for GRIZZLY 700 FI YFM7FGPX

Brands by name

Popular brands

Load more brands