manualshive.com logo in svg

Yamaha EK40G, Service Manual

The Yamaha EK40G is a versatile and reliable electronic keyboard, perfect for beginners and professionals alike. Unlock its full potential with the comprehensive Service Manual available for download, free of charge, at [website]. This manual provides vital information, troubleshooting tips, and step-by-step instructions to ensure optimal performance and endless hours of musical enjoyment.

Share
Download
background image

LOWR

6H95G11

LOWR

Lower unit

Special service tools  ................................................................................... 6-1

Lower unit (EK40G) ...................................................................................... 6-5

Removing the lower unit .......................................................................... 6-5
Removing the water pump and shift rod  ................................................. 6-5
Checking the water pump and shift rod  .................................................. 6-5

Propeller shaft housing  ............................................................................. 6-11

Removing the propeller shaft housing assembly  .................................. 6-13
Disassembling the propeller shaft assembly  ......................................... 6-13
Disassembling the propeller shaft housing  ........................................... 6-13
Disassembling the forward gear ............................................................ 6-14
Checking the propeller shaft housing  .................................................... 6-14
Checking the propeller shaft .................................................................. 6-14
Assembling the forward gear ................................................................. 6-14
Assembling the propeller shaft assembly .............................................. 6-14
Assembling the propeller shaft housing  ................................................ 6-15

Drive shaft and lower case  ....................................................................... 6-16

Removing the drive shaft ....................................................................... 6-17
Disassembling the lower case ............................................................... 6-17
Checking the pinion gear ....................................................................... 6-17
Checking the bearings ........................................................................... 6-17
Checking the drive shaft ........................................................................ 6-17
Checking the lower case and lower case cap ....................................... 6-18
Assembling the lower case .....................................................................6-18
Installing the drive shaft ......................................................................... 6-19
Installing the propeller shaft housing ......................................................6-19
Installing the water pump and shift rod  ................................................. 6-20
Installing the lower unit .......................................................................... 6-21

Shimming .................................................................................................... 6-23

Shimming ............................................................................................... 6-24
Selecting the pinion shims ..................................................................... 6-24
Selecting the forward and reverse gear shims .......................................6-24
Backlash ................................................................................................ 6-25
Measuring the forward and reverse gear backlash  ............................... 6-25

Lower unit (EK40J)  .................................................................................... 6-27

Removing the lower unit ........................................................................ 6-31
Removing the water pump and shift rod  ............................................... 6-32
Checking the water pump and shift rod  ................................................ 6-32

 6H95G11_06  04.8.6 9:32  Page 2

Summary of Contents for EK40G









































































































































































































Reviews:

No comments

Related manuals for EK40G

Yamaha FT25B Owner'S Manual preview
FT25B
Brand: Yamaha Pages: 86
BCM Advanced Research Advanced Socket 370 User Manual preview
Advanced Socket 370
Brand: BCM Advanced Research Pages: 38
MSI Z270 Gaming Pro Carbon Motherboard User Manual preview
Z270 Gaming Pro Carbon Motherboard
Brand: MSI Pages: 92
Texas Instruments TPA3121D2 User Manual preview
TPA3121D2
Brand: Texas Instruments Pages: 9
Sapphire Audio PP-I7RS400 PURE PERFORMANCE II User Manual preview
PP-I7RS400 PURE PERFORMANCE II
Brand: Sapphire Audio Pages: 44
Wiznet WizFi360-EVB-Pico Getting Started Manual preview
WizFi360-EVB-Pico
Brand: Wiznet Pages: 29
Gigabyte GA-EP43T-USB3 User Manual preview
GA-EP43T-USB3
Brand: Gigabyte Pages: 96
JETWAY 611CF User Manual preview
611CF
Brand: JETWAY Pages: 57
Gigabyte GA-M52S-S3P User Manual preview
GA-M52S-S3P
Brand: Gigabyte Pages: 96
Infineon TLE986 Evalboard Series User Manual preview
TLE986 Evalboard Series
Brand: Infineon Pages: 20
MSI MS-7174 Manual preview
MS-7174
Brand: MSI Pages: 32
Gigabyte GA-EP43T-S3L User Manual preview
GA-EP43T-S3L
Brand: Gigabyte Pages: 96
Texas Instruments TAS5001-5122C2EVM User Manual preview
TAS5001-5122C2EVM
Brand: Texas Instruments Pages: 27
Dynatem CPU-71-10 User Manual preview
CPU-71-10
Brand: Dynatem Pages: 57
Intel D845GVAD2 Quick Reference preview
D845GVAD2
Brand: Intel Pages: 36
Texas Instruments LMQ61460EVM-400K User Manual preview
LMQ61460EVM-400K
Brand: Texas Instruments Pages: 20
Biostar G31-M4 Setup Manual preview
G31-M4
Brand: Biostar Pages: 45
IEI Technology KINO-AQ170 User Manual preview
KINO-AQ170
Brand: IEI Technology Pages: 161

Brands by name

Popular brands

Load more brands