manualshive.com logo in svg

Yamaha EK40G, Service Manual, Page: 118 / 200

Share
Download
Yamaha EK40G Service Manual Download Page 118

LOWR

6-19

6H95G11

Lower unit

4.

Install the thrust bearing and roller bear-
ing assembly.

NOTE:

Apply gear oil to the inside and outside of the
thrust washer and roller bearing outer race
before installation.

Installing the drive shaft

1.

Install the roller bearing, then the drive
shaft, original shim(s), pinion, and circlip.

NOTE:

Take care the rollers will not fall off.

Installing the propeller shaft housing

1.

Install the washer 

1

and propeller shaft

assembly 

2

into the propeller shaft

housing assembly 

3

.

2.

Install the forward gear assembly to the
propeller shaft housing assembly.

3.

Apply grease to new O-rings.

4.

Fit the new seal into the lower case cap.

NOTE:

Cut the seal so that it projects out 

a

about

0.8 mm (0.03 in) from the lower case cap.

c

C

Do not pull the seal.

9

6F660770

0

6F660910

1

2

3

a

a

6F660807

6F660790

Ball bearing attachment 

9

:

90890-06631

Driver rod LS 

0

:

90890-06606

 6H95G11_06  04.8.6 9:32  Page 22

Summary of Contents for EK40G









































































































































































































Reviews:

No comments