Yamaha EK40G Page 52 Service Manual Download

Page: 52 / 200

FUEL

4-11

6H95G11

Fuel system

Adjusting the throttle stop screw

Start the engine and warm it up for 5 min-
utes.

Turn the throttle stop screw

in direc-

tion

until the specified engine idle

speed is obtained.

NOTE:

To increase the idle speed, turn the throttle
stop screw in direction

To decrease the idle speed, turn the throttle
stop screw in direction

Install a new O-ring

, and new gasket

, onto the carburetor body of the gaso-

line side, and then install the carburetor
body of the kerosene side.

Install the pilot screw, turn it in until it is
lightly seated, then out the specified
number of turns.

NOTE:

Adjust the throttle cable whenever the car-
buretor has been disassembled or the
engine idle speed has been adjusted.

For adjustment procedures, see Chapter3.

Install the carburetor assembly.

6H940110

Engine idle speed:

1,050—1,150 r/min

6H940150

Pilot screw setting:

3/4 —1 1/4 turns out

6H95G11_04 04.8.6 8:36 Page 12

Summary of Contents for EK40G









































































































































































































Search results

Summary of Contents for EK40G

Reviews:

Related manuals for EK40G

Brands by name

Popular brands

Yamaha EK40G, Service Manual

Search results

Summary of Contents for EK40G

Reviews:

Related manuals for EK40G

Brands by name

Popular brands