Yamaha EK40G Page 140 Service Manual Download

Page: 140 / 200

LOWR

6-41

6H95G11

Lower unit

Assembling the forward gear

Install a new taper roller bearing into the
forward gear using a press.

Assembling the drive shaft

Install a new drive shaft bearing onto the
drive shaft using a press.

Installing the drive shaft

Install the forward gear, then the drive
shaft assembly, spacer, pinion, and pin-
ion nut.

Tighten the nut to the specified torque.

Installing the oil seal housing

Install a new O-ring

, new gasket

, oil

seal housing

, and the dowels

Installing the propeller shaft housing

Install the original shim(s)

, washer

and propeller shaft assembly

into the

propeller shaft housing assembly

Apply grease to new O-rings.

Add or remove shim(s), if necessary, if
replacing the reverse gear, propeller shaft
housing, or lower case.

6B460310

6F660330

6F660320

Bearing inner race attachment

90890-06640

6F60300

Bearing inner race attachment

90890-06644

Drive shaft holder 3

90890-06517
Pinion nut holder

New: 90890-06715

Current: 90890-06505

Pinion nut:

74 N·m (7.4 kgf·m, 54.6 ft·lb)

6H95G11_06 04.8.11 13:01 Page 44

Summary of Contents for EK40G









































































































































































































Search results

Summary of Contents for EK40G

Reviews:

Related manuals for EK40G

Brands by name

Popular brands

Yamaha EK40G, Service Manual

Search results

Summary of Contents for EK40G

Reviews:

Related manuals for EK40G

Brands by name

Popular brands