Yamaha EK40G Page 90 Service Manual Download

Page: 90 / 200

POWR

5-33

6H95G11

Power unit

Insert the bushing

into the body

Place the height ring

in the body.

NOTE:

Align the slot in the height ring with the slot in
the body.

Set the spacer on the crank 2 (or crank
4).

Set crank 2 (or crank 4) on the special
service tool.

Mount the washers, roller bearing, and
connecting rod on the crankpin.

NOTE:

Take care so that spacer C

does not fall

out of the crank, turn the crank over so that
the crankpin is on top, and then insert the
crank into the special service tool.

The model number

on the connecting

rod should face up.

6F650540

6F650530

Bushing-9 (D30)

: 90890-02363

Body

: 90890-02352

Flange

: 90890-02351

Height ring (H-18)

90890-02401

Spacer C

: 90890-02404

6B450650

6H95G11_05 04.8.20 11:05 Page 34

Summary of Contents for EK40G









































































































































































































Search results

Summary of Contents for EK40G

Reviews:

Related manuals for EK40G

Brands by name

Popular brands

Yamaha EK40G, Service Manual

Search results

Summary of Contents for EK40G

Reviews:

Related manuals for EK40G

Brands by name

Popular brands