manualshive.com logo in svg

Yamaha EK40G, Service Manual, Page: 74 / 200

Share
Download
Yamaha EK40G Service Manual Download Page 74

POWR

5-17

6H95G11

Power unit

2.

Remove the flywheel magnet.

c

C

To prevent damage to the engine or tools,
screw in the flywheel puller set bolts
evenly and completely so that the fly-
wheel
puller plate is parallel to the flywheel mag-
net.

NOTE:

Apply force to the crankshaft end until the fly-
wheel magnet comes off the tapered portion
of the crankshaft.

3.

Remove the Woodruff key.

6B450090

Removing the electrical components

1.

Remove the bracket 

1

. (W: CDI unit,

starter motor, starter relay and rectifier)

2.

Remove the base assembly 

2

.

3.

Remove the spark plug caps from the
spark plugs, and then remove the ignition
coil 

3

.

Removing the throttle pulley assembly

1.

Removing the throttle pulley assembly.

6F650210

2

3

1

6F650230

Flywheel puller: 90890-06521

 6H95G11_05  04.8.6 11:01  Page 18

Summary of Contents for EK40G









































































































































































































Reviews:

No comments