Yamaha EK40G Page 135 Service Manual Download

Page: 135 / 200

6H95G11

6-36

Propeller shaft housing

Assembling the propeller shaft
housing

Install the needle bearing into the pro-
peller shaft housing to the specified
depth.

NOTE:

Install the needle bearing with the manufac-
ture identification mark

facing toward the

oil seal (propeller side).

Apply grease to new oil seals, and then
install them into the propeller shaft hous-
ing.

NOTE:

Install an oil seal halfway into the propeller
shaft housing, then the other oil seal.

Install the washer

and new ball bear-

ing

onto the reverse gear

using a

press.

Install the reverse gear assembly into the
propeller shaft housing using a press.

6F660150

6F660170

6F660180

6F660160

Driver rod SS

: 90890-06604

Needle bearing attachment

90890-06614

Bearing depth plate

90890-06603

Bearing inner race attachment

90890-06639

Needle bearing attachment

90890-06608

Driver rod LS

: 90890-06606

Ball bearing attachment

90890-06637

Depth

25.5 mm (1.0039 in)

6H95G11_06 04.8.11 13:01 Page 39

Summary of Contents for EK40G









































































































































































































Search results

Summary of Contents for EK40G

Reviews:

Related manuals for EK40G

Brands by name

Popular brands

Yamaha EK40G, Service Manual

Search results

Summary of Contents for EK40G

Reviews:

Related manuals for EK40G

Brands by name

Popular brands